HDMI - SXW & HDMI - EXW

HDMI EXTENDER

USER MANUAL V1.3 HDMI-SXW / HDMI-EXW

 
HDMI-SXW-EXW-เนื้อ.png

HDMI-SLW

HDMI-ELW

(Local)

HDMI-SXW-EXW-เนื้อ.png

HDMI-SRW

HDMI-ERW

(Remote)

Package Contents

  • 1x HDMI-SLW or HDMI-ELW Local Unit

  • 1x HDMI-SRW or HDMI-ERW Remote Unit

  • 1 user manual

  • 2x Power adapter DC 12V with lock

  • 1x HDMI 1.2M cable

  • 1x IR Blaster Cable(Peak Wavelength 940nm)

  • 1x IR Receiver Cable

  • 4x screws

  • 8x foot pads

Anything any missed, please contact your vendor.

Features

  • Through the HDMI Extender, you can use one DVD to display identical image and extension of HDMI signal up to 70/100 meters on HDTV

  • HDCP Compliant

  • Supports 3D pass-through

  • Supports CEC pass-through

  • Support RS-232(Bi-direction transfer)

  • Supports all frequency band IR control

  • One CAT.5 cable extension

  • Supports HDTV up to 4K2K

  • HD-based technology

  • Use CAT.5 cable to install easily

  • Cable Distance

Features

features.jpg

Specifications

spec.jpg

LOCAL FRONT VIEW

1. IR OUT

2. HDCP LED

3. LINK LED

4. MODE LED

5. POWER LED

FRONT-VIEW.png

LOCAL REAR VIEW

1. Power jack (12V DC)

2. LINK (RJ-45 Connector)

3. HDMI BYPASS(Only HDMI-ELW)

4. HDMI IN

5. RS-232

FRONT-VIEW.png

REMOTE FRONT VIEW

FRONT-VIEW.png

1. IR2 IN

2. IR1 IN

3. HDCP LED

4. LINK LED

5. MODELED

6. POWER LED

REMOTE REAR VIEW

FRONT-VIEW.png

1. Power jack (12V DC)

2. LINK (RJ-45 Connector) 3. HDMI OUT

4. RS-232

Installation

1. Turn off the DVD and HDTV.

2. Connect the HDMI extension cable between the DVD and the “HDMI IN” port of HDMI-SLW or HDMI-ELW.

3. Connect the HDMI extension cable between the HDTV and the “HDMI OUT” port of HDMI-SRW or HDMI-ERW.

4. Connect the CAT.5 cables between the HDMI-ELW “LINK” port and the HDMI-SRW or HDMI-ERW “LINK” port of the extender.

5. Connect the power cord and turn on the extender.

6. Turn on the DVD and HDTV. ※When HDMI-ELW is in BYPASS mode the LINK port should be left unused.

IR Receiver Cable Directions:

Put it into the HDMI-SRW or HDMI-ERW “IR2 IN” port and place the IR Receiver Cable, so that you can point to it easily with your IR remote controller.

IR Blaster Cable Directions:

Plug IR blaster cable plug into HDMI-SLW or HDMI-ELW “IR OUT” port, It sits in front of the DVD receiver’s IR sensor, which is located on the front-panel.

Additional Options

Select any additional options you may require.

1. IR Receiver Cable

Additional-Options.png

2. IR Blaster Cable

Additional-Options.png

Technical Specifications Output Signal

Technical-Specifications-Output-Signal.p
pin.jpg

Wiring Information & Coding

Wiring.png
pair.jpg
pin1.jpg

RS232/D - Sub 9 Pin Definitions

nrs232.png

Note

       However sometimes, especially in demonstrations or in a lab environment, the cable is rolled randomly in small turns for convenience. The randomly rolled UTP cable suffers additional signal impairments (compared to a straight cable) and therefore the maximal operating reach might be reduced.

       Rolling a CAT5E cable around a 70 cm fixed diameter plastic drum has just a minor effect on the FEXT (Far End Cross Talk) when compared to a fully stretched cable.

note.png

© C&C TECHNIC TAIWAN CO., LTD. All rights reserved

Trademarks: All the companies, brand names, and product names referred to in this manual are the trademarks or registered trademarks belonging to their respective companies.