top of page

HDMI - SXC & HDMI - EXC

​

HDMI EXTENDER

USER MANUAL V1.3 HDMI-SXC / HDMI-EXC

Anchor 1
HDMI-SXW-EXW-เนื้อ.png

HDMI-SLC

HDMI-ELC

(Local)

HDMI-SXW-EXW-เนื้อ.png

HDMI-SRC

HDMI-ERC

(Remote)

Package Contents

  • 1 × HDMI-SLC or HDMI-ELC Local Unit

  • 1 × HDMI-SRC or HDMI-ERC Remote Unit

  • 1 × User Manual

  • 2 × DC 12V Power Adapters with Lock

  • 1 × 1.2 m HDMI Cable

  • 1 × IR Blaster Cable (Peak Wavelength: 940 nm)

  • 1 × IR Receiver Cable

  • 4 × Screws

  • 8 × Foot Pads

Anything any missed, please contact your vendor.

Features

  • Use an HDMI Extender to distribute the same video source to multiple HDTV displays and extend HDMI signals up to 70/100 meters.

  • HDCP Compliant

  • Supports 3D Pass-Through

  • Supports CEC Pass-Through

  • Supports RS-232 Bi-Directional Transmission

  • Supports Full-Band IR Control

  • Extends signals through a single CAT.5 cable

  • Supports HDTV resolutions up to 4K2K

  • Based on HDBaseT™ technology

  • Easy installation using CAT.5 cable

  • Cable Distance

Features

edit-features.jpg

Specifications

edit-spec.jpg

Local Unit Front View

1. IR OUT

2. HDCP LED

3. LINK LED

4. MODE LED

5. POWER LED

FRONT-VIEW.png

Local Unit Rear View

1. Power jack (12V DC)

2. LINK (RJ-45 Connector)

3. HDMI BYPASS(Only HDMI-ELW)

4. HDMI IN

5. RS-232

FRONT-VIEW.png
FRONT-VIEW.png

Remote Unit Front View

1. IR2 IN

2. IR1 IN

3. HDCP LED

4. LINK LED

5. MODELED

6. POWER LED

FRONT-VIEW.png

Remote Unit Rear View

1. DC 12V Power Jack

2. LINK (RJ-45 Connector) 3. HDMI OUT

4. RS-232

Installation

  • Turn off the DVD player and HDTV.

  • Connect an HDMI cable between the DVD player and the HDMI IN port of the HDMI-SLC or HDMI-ELC Local Unit.

  • Connect an HDMI cable between the HDTV and the HDMI OUT port of the HDMI-SRC or HDMI-ERC Remote Unit.

  • Connect a CAT.5 cable between the LINK port of the HDMI-ELC Local Unit and the LINK port of the HDMI-SRC or HDMI-ERC Remote Unit.

  • Connect the power adapters and power on the extender units.

  • Turn on the DVD player and HDTV. When the HDMI-ELC is operating in BYPASS mode, the LINK port should remain unused.

IR Receiver Cable Directions:

Connect the IR Receiver Cable to the IR2 IN port of the HDMI-SRC or HDMI-ERC Remote Unit. Place the IR Receiver Cable in a convenient location where it can easily receive signals from the IR remote control.

IR Blaster Cable Directions:

Connect the IR Blaster Cable to the IR OUT port of the HDMI-SLC or HDMI-ELC Local Unit. Position the IR Blaster in front of the DVD player's IR sensor, which is located on the front panel.

Additional Options

Select any additional options you may require.

1. IR Receiver Cable

Additional-Options.png

2. IR Blaster Cable

Additional-Options.png

Technical Specifications Output Signal

Technical-Specifications-Output-Signal.p
pin.jpg

Wiring Information & Coding

Wiring.png
pair.jpg
pin1.jpg

RS232/D - Sub 9 Pin Definitions

nrs232.png

Note

       In demonstrations or laboratory environments, UTP cables are often coiled for convenience. Cable coiling may introduce minor signal degradation, which can slightly reduce the maximum transmission distance compared to a straight cable.

 

       However, coiling a CAT5E cable around a 70 cm diameter drum has only a minimal impact on Far-End Crosstalk (FEXT) compared with a fully extended cable.

note.png

© C&C TECHNIC TAIWAN CO., LTD. All rights reserved

Trademarks: All company names, brand names, and product names mentioned in this manual are trademarks or registered trademarks of their respective owners.

bottom of page